Modul CS

Advantages at a glance

  • Stabilising leg or liquid and bulk tippers (rear) 
  • Support while unloading
  • Levelling due to two seperate landing gears
  • Low maitenance because of integrated lubricant cartridge
  • High degree of installation variability thanks to double bolt hole pattern
  • Additional spindle nut
    - Additional protection against wear and tear
    - Minimal risk of accidents

Technical Features

  • Protected against wear by fully sealed gearbox and reinforced inner tube
  • Full length back plate for high variability during installation
  • Reinforcement for maximum bending strength
  • Heavy duty shaft for better shock resistance
  • Secure stand due to reinforced rigid foot

Technical Specification

 

* Bracing lugs are supplied loose


Note: 

Dimensions A, B and C, see general information.
Also available without brace lugs on request

Selection table / Versions available

Order No. M (mm) H (mm) P (mm) Back plate Foot
CS 1044700R 750 470 728 full length T rigid
CS 1054700R 700 380 678 full length T rigid
CS 1064700R 650 380 628 full length T rigid
CS 1084700R 600 330 578 full length T rigid
CS 1094700R 550 280 528 full length T rigid

Technical Data (per piece / set)

Characteristic Value
Lifting capacity 12 t/ 24 t
Static load 33 t / 66 t
Lift per turn of handle  
- Low gear 0,9 mm
- High gear 15,0 mm
Crank force at 8 t lifting capacity 110 N

Remarks

Please order crank handle separately, see general information.

Two stabiliser legs are required per trailer.

There is no cross shaft.

Modul CS

Spare parts

Item Description Remark Order No. per set
1 Cover JS E0046300 1
2 Bevel gear with bolts JS E0058600 1
3 Cover compl. with bearing compl. JS E0083900 1
3 Cover with bearing compl. from series 0072322 KW 10/2006 JS E0083901 1
4 Grease nipple with protective cap JS E0084000 1
5 Shaft with bearing JS E0084100 1
6 Grease tank JS E0002000 1
7 Gear JS E0055800 1
8 Crank shaft compl. JS E0046500 1
9 Bearing holder compl. JS E0058800 1
10 Crank shaft and bearing holder compl. with 08 + 09 JS E0056600 1
11 Drive compl. with 05, 07 + 10 JS E0084300 1
12 Bolts, washers, nuts JS E0043100 1
13 Crank 350 mm w. parking hook with 12, 14 + 15 JS U01 1
13 Crank 415 mm w. parking hook with 12, 14 + 15 JS U02 1
13 Crank 450 mm w. parking hook with 12, 14 + 15 JS U03 1
13 Crank 480 mm w. parking hook with 12, 14 + 15 JS U04 1
13 Crank 520 mm w. parking hook with 12, 14 + 15 JS U05 1
13 Crank 570 mm w. parking hook with 12, 14 + 15 JS U07 1
13 Crank 620 mm w. parking hook with 12, 14 + 15 JS U08 1
14 Crank bushing JS E0042700 1
15 Crank parking hook for crank 350mm (JS U01) JS E0040200 1
15 Crank parking hook for crank 415-480mm (JS U02 - JS U04) JS E0040201 1
15 Crank parking hook for crank 520mm (JS U05 - JS U08) JS E0040202 1
16 Mh-04/750 shaft right JS E0068303 1
16 Mh-05/700 shaft right JS E0068302 1
16 Mh-06/650 shaft right JS E0068301 1
16 Mh-08/600 shaft right JS E0068304 1
16 Mh-09/550 shaft right JS E0068305 1
17 Axial bearing JS E0066400 1
18 Mh-06/650 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067001 1
18 Mh-05/700 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067002 1
18 Mh-04/750 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067003 1
18 Mh-08/600 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067004 1
18 Mh-09/550 inner tube r. + spindle and bearing with 17 + 03 (JS E0083901) JS E0067005 1
19 Angle JS E010.001 1

Modul CS

Modul CS

PDF-Downloads


Mounting and Operating Instructions
Modul Landing gear 06/2010
Modul CS 06/2010
 
Flyer
MODUL CS Stabilizer leg 09/2016