General information

Drawbars are the connection between the tractor and the steerable drawbar trailer. They are designed to be mounted on a pivot support.

Drawbars are parts that are subject to type approval and that connect vehicles, and are therefore subject to the highest safety requirements. They may only be operated with the compliant towing hitches and towing eyes that have been approved. Changes of any kind (except for the ones allowed under 2.2) exclude guarantee claims and type approval is forfeited and thus the vehicle operating licence as well.

Drawbars are produced in accordance with the Directives 94 / 20 EC and ECE-R55 Class E. The assembly may only be completed by authorised specialist companies and according to the applicable Directives and national approval regulations. For Germany, §§ 19, 20 and 21 of the StVZO (German Road Traffic Licensing Regulations) apply. In addition, the conditions of §13 FZV relating to the duty of  notification for alteration of vehicle data are to be adhered to.



1. Characteristics and range of application

The permissible load conditions for drawbars can be seen on the inscription on the factory name plate or the product overview table or the respective catalogue pages. They apply to the intended use in compliance with the Directive 94 / 20 EC or ECE-R55. In the case of additional dynamic stress, e.g. operation on uneven road surfaces, construction sites and forestry, the D value should not be fully exploited or a stronger drawbar should be used i.e. enquiries should be made at ROCKINGER. Decisive for the selection of a drawbar is the D value as well as the permissible front axle load of the turning steering frame onto which it is to be attached. Specifications for the permissible maximum weight of the trailer can be used as an orientation guide and serve only as a recommendation.

The suitability of a drawbar for the combination of vehicles can be checked using the specified D value.

Truck and steerable drawbar trailer: The D value

• Theoretical drawbar force between truck and trailer, calculated reference value of forces between the moving masses
• The D value can only be calculated by the permissible total weight of both measures (truck and steerable drawbar trailer)
• Calculating the D value (kN):

T : Total weight of the truck in t
R : Total weight of the steerable drawbar trailer in t
g : acceleration due to gravity, 9.81 m / s2

The calculated D value may be the less than or equal to the D value of the drawbar.

When combining vehicles, it must be ensured that the angle (up or down) of the towing eye is not greater than 3° to the horizontal axis. Greater deviations may lead to premature wear or even damage to the drawbar.



2. Assembly instructions

2.1. Assembling pivots

We primarily recommend the use of Silentbloc bushes for the bearing of drawbars. Silentbloc bushes reduce wear and maintenance work and increase comfort.

Drawbars with Silentbloc bushes (1):

Screws (M 30-8.8) should primarily be used to fasten the drawbar. The torque of the self-locking nut should be 400 Nm for this. This effectuates the clamping action of the Silentbloc, which ensures the functionality of the radial motion using the rubber  element. When first assembling the screw, it should be inserted with standard  lubricating grease or assembly paste, to facilitate disassembly at a later point in time. The bearing does not need to be lubricated. In order to avoid damage to the Silentbloc bushes,the vertical pivoting angle of the drawbar should not exceed ± 20°. Using Silentbloc bushes for drawbars fitted with a drawbar height adjustment device is therefore not recommended.

Spring bolts can also be used to fasten Silentbloc bushes. The assembly instructions (2) are also to be observed.

Drawbars with brass / bronze wear bushes (2)

During assembly, it must be ensured that the drawbar remains vertically movable; in the bearing, however, it must be free from play. For fastening, spring bolts may be used in combination with washers / castle nuts / split-pins or washers / self-locking hex-nuts. The torque of the castle nut should be at least 180 Nm. The spring bolt  should be lubricated with standard lubricating grease or assembly paste prior to  assembly. During operation, the spring bolt must be regularly greased (according to the trailer’s specified maintenance intervals), or be connected to a centralised  lubricating system.

2.2. Assembly of mounting parts / repair welding

There are boreholes and eyeholes on the cross struts for attaching fastening fixtures  for the mounting of height adjustment systems, dummy couplings and the like. Furthermore, additional mounting points can be mounted on the longitudinal struts using suitable clamping fixtures (e.g. spring shackles for GHE).

If the aforementioned options are not sufficient, hooks or eyeholes can be welded  onto the longitudinal struts. When doing so, it must be ensured that they are circumferentially fillet welded (a = 3mm) to the profile centreline.

Modification or repair welding and straightening work on drawbars is strictly prohibited.

2.3. Assembling a Height Adjustment System

The height adjustment system is to be assembled such that the mounted drawbar fulfils requirements for ground clearance and height adjustment of the drawbar eye. The drawbar must clear the ground. Ground clearance must be at least 200 mm,  even when dropping the drawbar from the horizontal position.

The height adjustment system must be constructed such that the drawbar can be  adjusted to the height of the towing hitch funnel on the tractor by one person without the use of tools or other aids. The drawbar eye must be free to move horizontally at least 300 mm up and down horizontal to the road surface with the height adjustment system. In this area, the drawbar must be infinitely adjustable or in steps no greater than 50 mm, measured at the drawbar eye. The height adjustment system may not impair the light manoeuvrability of the drawbar after successful coupling.

2.4. Note on GZU, GZL, GZHL, GZLG, GZV, GZHU

Extendable towing pipe: The fixing and clamping screws are to be tightened in  accordance with the information on the associated catalogue page. The towing pipe may not be greased.

2.5 Note on GZN 12 and 26

GZN 12 & 26: The tightening torque of the castle nut (SW70) is min. 500 Nm.  Caution: If the splint cannot be inserted, you must continue to screw in up to the next splint hole cover. Never turn the castle nut backwards!

2.6. Note on GZLV (pneumatically lockable)

Pneumatic operation vents for locking / unlocking are not included. The spring loaded cylinder can be connected for single-action with a sinter filter or for double-action. Please note the separate instruction manual for GZLV.

2.7. Note: GSG and GSZ (pivoting towing eyes)

Operation: Release the spring cotter, unscrew the locking bolt by hand, remove the pin bolt, swivel the drawbar by 180°, and refasten and secure in reverse order.



3. Inspection and maintenance notes

Drawbars are subject to normal wear due to stress occurring during normal operation. Therefore, they must be checked with respect to the following criteria at regular intervals and, if necessary, repaired.

3.1. Mounting and securing elements

Mounting and securing elements may not be loose or damaged. Loose mounting elements are to be tightened according to the specified torques, damaged mounting or securing elements must be replaced.

3.2. Pivot play

Longitudinal play max. 2 mm, latitudinal play max. 4 mm for bronze or plastic bearings. No play is allowed for Silent bearings. Separation of bearing material is not permissible. (Technical Inspection Authority data sheet 712)

3.3. Drawbar struts, drawbar eye shaft, welding seams

Drawbar struts (longitudinal or latitudinal), drawbar eye shafts and welding seams may not exhibit any mechanical damage or be overly corroded. Drawbars with deformations, cracks or breakages as a result of improper use are no longer roadworthy. They may neither be straightened nor repaired in any other way but must be replaced by new drawbars.

3.4 Towing eyes / Maintenance / Inspection

In order to achieve a long tool life of the towing eye, one has to grease the towing eye before initial operation or after longer operation with viscous, if possible water-proof, grease (EP3). Towing eyes may not be damaged or worn. Knocked out or loose wear bushes must be replaced in time. Distorted or twisted towing eyes may not be straightened under any circumstances –> Risk of accident.


Wear limit:

DIN / CH b¹ max. (mm) c min. (mm) e² min. (mm)
74054 41,5 28,0 22,0
74053 52,5 41,5 23,5
Heavy duty / ECE 52,5 41,5 21,0
Drawbar eye CH 41,5 36,5 29,5
11026 41,5 38,0 22,0
Skand. 57 mm 59,5 19,0 -

1 Measuring with bush
2 Measuring without bush

3.5. Height adjustment system (HAS)

HASs may not be loose, damaged or corroded. Damaged or overly corroded parts of the HAS must be replaced. The functionality of the HAS must fulfil the requirements specified in section 2.3.



4. Surface treatment

Optimum protection against corrosion up to a length of 3400 mm thanks to cathodic e-coating with zinc phosphate (EPD Zn). A subsequent top coat is not necessary in normal circumstances.

Drawbars longer than 3400 mm are blasted and grounded with Synthal-KH. Lasting protection against corrosion is ensured without the customer needing to add a final coat.

5. Identification instructions

Drawbars are components which must be identified. The permissible load conditions can be seen on the inscription on the factory name plate.

1. Type
2. Item No.
3. Permissible D value in kN
4. EC Authorisation
5. Permissible front axle load
6. ECE-R55 authorisation



6. Annotation

Special models with a certificate for the issuance of individual authorisation in accordance with §13 FzTV in connection with § 22a StVZO are given individual approval (TP No.). The associated certificate is sent separately and is to be provided with the vehicle papers.

ROCKINGER has appropriate EC and ECE type approved drawbars for almost all vehicle combinations. In order to meet the requirements of the market, further type approvals are planned, and existing ones are being extended and added to. For this reason, all drawbars are subject to changes that are conducive to technical progress.
We would be happy to answer any further questions.

LubeTronic 5Point

Item Description Version* Remark Order No.
01 LubeTronic 5Point SK 0xxxx00, SK 0xxxx04 MAN version, compl. with fixing kit and item 3, for JSK 37 C, JSK 42 SKE010790700
01 LubeTronic 5Point SK 0xxxx01 MAN version, compl. with fixing kit and item 3, for JSK 38 C SKE010790800
01 LubeTronic 5Point SK 0xxxx03, SK 0xxxx05 Volvo version, compl. with fixing kit and item 3, for JSK 37 C, JSK 42 SKE006250310
01 LubeTronic 5Point SK 0xxxx15 JOST-„Standard” / Mercedes-Benz version, compl. with fixing kit and item 3, for JSK 37 C, JSK 42 SKE010791500
01 LubeTronic 5Point SK 0xxxx16 JOST-„Standard” / Mercedes-Benz version, compl. with fixing kit and item 3, for JSK 38 C SKE010791600
02 Connection cable For LubeTronic 5Point JOST-„Standard” SKE005680100
03 Lubrication tube 1,6m Fits all LT5Ps SKE006620200
04 JOST High Performance Lubricant Refill set (2 cartridges á 400ml) SKE005670000
05 JOST High Performance Lubricant 25kg barrel SKE007090000
06 Push-in fitting 5x NTE003030000

 

* When ordering, please state the design mounted on the vehicle. You will find the design on the type plate of the lubrication pump.

** The model SK0040800 has been replaced. Please order SK 006250200 and
connection cable SKE005680100.

 

Attention: The retrofitting of standard fifth wheel couplings with LubeTronic 5Point ist not possible.

Technical Specification

Sensor coupling system in accordance with the ECE R55-01, TÜ.EGG.095-05, DIN 74081, ISO 3842, ECE R10 directives/standards. Suited for picking up 2” kingpins (class G50) in accordance with ECE R55-01, DIN 74080, ISO 337 and steering wedges in accordance with ECE R55-01, DIN 74085.

 

 

Did you know …

… … that the LubeTronic 5Point relubrication system can only be used with JOST highperformance lubricant (available in 2 x 800 g cartridges (JOST Order No.: SKE005 670 000) or in a 25 kg barrel (JOST Order No.: SKE007 090 000))? The fully-synthetic lubricant is particularly temperature-resistant (between –20°C and +80°C) and adheres particularly well to metal surfaces, thus guaranteeing that LubeTronic 5Point functions correctly. The guarantee excludes the use of other types of grease!


PDF-Downloads


Mounting and Operating Instructions
LubeTronic 5Point Refilling instruction 02/2013
LubeTronic 5Point mounting and operating instruction 07/2012
 
Repair kits
LubeTronic 5Point Testing instructions (MAN) 02/2017
LubeTronic 5Point Testing Instructions Standard 02/2017
LubeTronic 5Point Repair Manual 05/2012
LubeTronic 5Point Testing Instructions (Volvo) 02/2017
 
Flyer
LubeTronic 5Point JOST High-Perfomance Lubricant 09/2016
LubeTronic 5Point The central lubrication system for fifth wheel couplings 09/2016
LubeTronic 5Point JOST High-Perfomance Lubricant 09/2014
Sales Information IVECO 08/2018
Sales Information MAN 08/2018
Sales Information Renault 08/2018
Sales Information Volvo 09/2016
Sales Information Volvo 08/2018
Sales information DAF 08/2018